• 欢迎来到萘析商城
当前位置: 首页 标准物质 有机类 单标 六甲基二硅氧烷
六甲基二硅氧烷_107-46-0,六甲基二硅氧烷
图片仅供参考,具体产品以实物为准!

六甲基二硅氧烷

BW901007 {{goodObj.price > 0 ? '¥' + goodObj.price : '咨询'}} ¥{{goodObj.sell_price || 0}} 咨询 107-46-0 1mL {{goodObj.date}} 秦境 {{item.norm}} 99.0% {{inventory}}
六甲基二硅氧烷介绍:

Reference Material

This certificate is designed in accordance with ISO 17034 and ISO Guide 31. This reference material (RM) was designed,produced and verified in accordance with ISO/IEC 17025, ISO 17034 and a registered quality management system ISO9001.

Product Name

Hexamethyldisiloxane

Product Code

BW901007

Lot Number

23041513

CAS No.

107-46-0

Mol. Formula

C6H18OSi2

Mol. Weight

162.38

Certified on

10 Apr 2023

Expiry Date

9 Apr 2025

Storage Temp

(0~4)°C

Specification

1.0mL

CERTIFIED

Purity

CERTIFIED

Expanded Uncertainty (U)

Approved by

99.0%

0.5%

Uncertainty

The certified value(s) and uncertainty(ies) are determined in accordance with ISO 17034 with an 95% confidence level (k=2). Uncertainty is based on the Total Combined Uncertainty, including uncertainties of characterisation, homogeneity and stability testing. Stability values are based on real evidence opposed to simulation.

The producer certifies that this reference material meets the specification stated in this certificate until the expiry date, provided it is stored unopened at the recommended temperature herein. Product warranties for this reference material are set out in the terms and conditions of purchase.

Intended Use

This RM is intended for use in a laboratory as a calibration and quality control standard or in method development for analytical techniques.

Safety

Proper precautions should be observed while handling. See Safety Data Sheet.

Traceability

The balances used for gravimetric measurements are calibrated with weights traceable to the national standards (DKD). The calibration of the balances is verified daily internally and annually by an external accredited calibration service. Chromatographic methods are traceable to the International System of Units (SI).

Homogeneity

Random replicate samples of the final packaged RM have been analysed to prove homogeneity compliant with ISO 17034.

Storage

The RM should be stored in the original sealed container at the indicated temperature.

Instructions for use

It is recommended to use 1 mg as the minimum sample size and if less material is used, to increase the certified uncertainty by a factor of two for half sample and four for a quarter of sample. If storage after opening is necessary, the RM should be tightly closed and kept from light and moisture. If the RM was in a sealed ampoule, it should be transferred to a vial with minimum head space.


您正在浏览的产品:六甲基二硅氧烷

手机版:六甲基二硅氧烷

本公司销售的所有产品仅供实验科研使用,不用于人体及临床诊断。

国家标准:GBZ/T 160.123-2004 工作场所空气中醇醚类化合物的测定方法
标准名称及标准号 GBZ/T 160.123-2004 工作场所空气中醇醚类化合物的测定方法
适用范围 适用于工作场所空气中六甲基二硅氧烷及其他醇醚类化合物的检测。
核心检测方法 气相色谱法(GC-FID),采用活性炭管采样,溶剂解吸后分析。
检出限与定量限 检出限为0.02 μg/mL,定量下限为0.05 μg/mL(基于采样体积15 L)。
质控样品要求 每批次样品需包含至少1个空白对照和1个加标回收样品,回收率应为80%-120%。
关键实验步骤 1. 采样:活性炭管以0.5 L/min流速采集15 L空气;
2. 解吸:二硫化碳解吸,振荡30分钟;
3. 分析:GC-FID进样,分离柱为DB-5毛细管柱。
特别说明 六甲基二硅氧烷易挥发,采样后需密封保存并尽快分析,避免长时间暴露于高温环境。
行业标准: 固定污染源废气 挥发性有机物的测定 固相吸附-热脱附气相色谱质谱法
标准名称及标准号 HJ 734-2014 固定污染源废气 挥发性有机物的测定 固相吸附-热脱附气相色谱质谱法
适用范围 适用于固定源废气中六甲基二硅氧烷等挥发性有机物的定性及定量分析。
核心检测方法 固相吸附管采集废气样品,热脱附后通过GC-MS分析。
检出限与定量限 方法检出限为0.05 μg/m³,定量限为0.15 μg/m³(基于采样体积3 L)。
质控样品要求 每20个样品需做1个平行样,相对偏差应≤20%;校准曲线R²≥0.995。
关键实验步骤 1. 采样:吸附管在恒流条件下采集废气;
2. 脱附:热脱附仪310℃解析,低温聚焦;
3. 分析:GC-MS全扫描模式,定量离子为m/z 147。
特别说明 需定期更换吸附管填料并验证脱附效率,避免交叉污染。
国家标准: 恶臭污染物排放标准
标准名称及标准号 GB 14554-1993 恶臭污染物排放标准
适用范围 适用于含六甲基二硅氧烷等有机硅类物质的恶臭污染物排放限值控制。
核心检测方法 嗅觉测定法结合仪器分析(如GC-MS),参考配套采样方法。
检出限与定量限 嗅觉阈值法规定最低可识别浓度为10 OU/m³。
质控样品要求 嗅觉测试需6人以上评价小组,仪器分析需定期校准传感器和检测器。
特别说明 六甲基二硅氧烷因其低嗅阈值需重点关注无组织排放的边界监控。

以上信息仅供参考,请以相应标准的原文为准!